316L STAINLESS STEEL PIPE SYSTEM
Using Tubepress® High Pressure Press Tools
APPLICATIONS – FLUIDS

40 BAR

Pn 40
4,000 Kpa
580 psi
D = 15 – 108 mm

Other applications other than fluids would need to be assessed by our technical department. Please provide details of the required system including sizing, temperature, operating pressure, medium to be conveyed plus other relevant details. IBEX Australia will then provide an analysis and resultant TUBEPRESS® series recommendation / warranty to be provided.

 

316L STAINLESS STEEL PIPE SYSTEM

Tubrepress logo grey box_2 STANDARD PRESSURE LOW PRESSURE
DIMENSION  /  STANDARD PRESSURE  DIMENSION  /  LOW PRESSURE
SERIES 9000 –
EPDM BLACK
D = 15 – 22 mm / Pn 40
D = 28 – 35 mm / Pn 40
D = 42 – 108 mm / Pn 40
40 bar 580 psi
40 bar 580 psi
40 bar 580 psi
D = 15 – 22 mm / Pn 40
D = 28 – 35 mm / Pn 25
D = 42 – 108 mm / Pn 16
40 bar 580 psi
25 bar 360 psi
16 bar 235 psi
SERIES 17000 –
HNBR YELLOW
D = 15 – 108 mm / Pn 5 5 bar 72.5 psi D = 15 – 108 mm / Pn 5 5 bar 72.5 psi
SERIES 18000 –
FKM (VITON) RED
D = 15 – 22 mm / Pn 40
D = 28 – 35 mm / Pn 40
D = 42 – 108 mm / Pn 40
40 bar 580 psi
40 bar 580 psi
40 bar 580 psi
D = 15 – 22 mm / Pn 40
D = 28 – 35 mm / Pn 25
D = 42 – 108 mm / Pn 16
40 bar 580 psi
25 bar 360 psi
16 bar 235 psi
SERIES 19000 –
FKM (VITON) GREEN


D = 15 – 22 mm / Pn 40
D = 28 – 35 mm / Pn 40
D = 42 – 108 mm / Pn 40
40 bar 580 psi
40 bar 580 psi
40 bar 580 psi
D = 15 – 22 mm / Pn 40
D = 28 – 35 mm / Pn 25
D = 42 – 108 mm / Pn 16
40 bar 580 psi
25 bar 360 psi
16 bar 235 psi
LARGE BORE
EPDM BLACK
D = 114 – 140 – 168 mm / Pn 16 16 bar 235 psi
TUBEPRESS® Must be pressed with Genuine HP TUBEPRESS® tooling to guarantee the above pressure ratings Using TUBEPRESS® LP Tooling Using other press tools*

– Max. operating pressure with compressed air: 30 bar (HP Equipment Only)
– Technical and Fuel gases refer to technical department.

Any TUBEPRESS® system operating above the low  pressure ratings must be pressed with TUBEPRESS® high pressure (HP) equipment and have safety control measures installed in the system; refer to the Technical Department.

Techinical applications need to be assessed by our technical department. Please provide details of required system sizing, temperature and operating pressure, medium to be conveyed plus other relevant details for an analysis and resultant recommendation / warranty to be provided.

 

* USING OTHER PRESS TOOLS

Using other manufactures press tools will affect pressure ratings & guarantees. TUBEPRESS® maybe pressed with other manufacturers press tools however Ibex Australia gives NO guarantee for the tightness of the press tools. The system will only be rated in most cases to 16 bar, please refer to technical department for further details.
  • The press tools must be maintained according to the respective manufacturer guidelines.
  • With fittings up to and including 54 mm in diameter, pressing jaws and slings for press connections of the typeM-MM must exhibit the original profiles SA, M or V.
  • Compact press tools up to and including 28 mm must have a minimum pressing force of 18 KN and a pin diameter of 10 mm
  • With fittings more than 54 mm in diameter, pressing jaws and slings for press connections of the type M-MM must exhibit the original profiles SA, M.
  • Press tools up to and including 54 mm and up to and including 108 mm (electronic) must have a minimum pressing force of 30 kN and a pin diameter of 14 mm.
  • The TUBEPRESS® installation instructions must be observed.

SPECIAL APPLICATIONS 40 BAR PLUS

TUBEPRESS® is safely operational at pressures in excess of the above standard pressure ratings. These special applications need to be assessed by IBEX Australia technical department. Please provide details of required system sizing, temperature and operating pressure, medium to be conveyed plus other relevant details for an analysis and resultant recommendation / warranty to be provided.

Any TUBEPRESS® system operating above standard pressure, MUST be pressed using TUBEPRESS® (HP) equipment and have safety control measures installed in the system; refer to IBEX Australia Technical Department.

Systems should be designed and installed suitable for the application to maintain integrity in accordance with the manufacture recommendation.