TP_15to22mm_1 1: Cut tube to length.  The tube ends must be clean with no scratches or grooves.Remove end caps.
TP_15to22mm_2 2: Deburr tube inside and outside.
TP_15to22mm_3 3: Witness mark the insertion depth on the tube.
TP_15to22mm_4 4: Select pressing jaw according to the fitting dimension and insert into the press tool.Close the retention pin of the tool.
TP_15to22mm_5 5: Check TUBEPRESS® fitting for correct placement of the sealing ring and push the end of the tube into the fitting by rotating it easily until it reaches a complete stop.The fitting outer edge must correlate with the witness mark.
TP_15to22mm_6 6: Open pressing jaw and place around fitting ensuring bead of the fitting connects into the groove of the pressing jaw.Commence pressing procedure by activating the start button on the press tool, hold down for 3 seconds to activate automatic function. Support tool throughout the press cycle and when complete remove from fitting.Do not allow interruption to the press cycle. In case of danger, an interruption of the pressing process is possible by pressing the emergency-stop button.After resetting emergency stop situation, re-press ensuring that press head is located in the same position as the fitting.

TUBEPRESS® 28mm UP TO 54mm


TP_15to22mm_1 1: Cut tube to length with planetary saw or tube cutters.The tube ends must be clean with no scratches or grooves.Remove end caps.
TP_15to22mm_2 2: Deburr tube inside and outside.
TP_15to22mm_3 3: Witness mark the insertion depth on the tube.
TP_15to22mm_5 4: Check TUBEPRESS® fitting for correct placement of the sealing ring and push the end of the tube into the fitting by rotating it easily until it reaches a complete stop.The fitting outer edge must correlate with the witness mark.
TP_28to54mm_5 5: Select intermediate jaw, fit to press tool and close the retention pin.Select suitable pressing slings and assemble on TUBEPRESS®fittings.
TP_28to54mm_6 6: Open the intermediate jaw by pressing the jaw levers down, connect jaw to pressing sling.Check whether fitting outer edge correlates with the marking of the insertion depth.Commence the pressing procedure by actuating the start button on the press tool, hold down for three seconds to activate automatic function.Do not allow interruption to the press cycle. In case of danger, an interruption of the pressing process is possible by pressing the emergency-stop button.After resetting emergency stop situation, re-press ensuring that press head is located in the same position on the fitting.

TUBEPRESS® 76mm UP TO 108mm

TP_76to108mm_1 1: Cut tube to length with planetary saw or tube cutters.The tube ends must be clean with no scratches or grooves.Remove end caps.
TP_76to108mm_2 2: Deburr tube inside and outside with a deburring tool.
TP_76to108mm_3 3: Witness mark the insertion depth on the tube.
TP_76to108mm_4 4: Check TUBEPRESS® fitting for correct placement of the sealing ring and push the end of the tube into the fitting by rotating it easily until it reaches a complete stop.The fitting outer edge must correlate with the witness mark.
TP_76to108mm_5 5: Select suitable pressing slings and assemble on TUBEPRESS® fitting.Please Note:  Press sling must be reset to original open position before each press
TP_76to108mm_6 6: Open the intermediate jaw by pressing the jaw levers down check whether fitting outer edge correlates with the marking of the insertion depth.Commence the pressing procedure by actuating the start button on the press tool, hold down for three seconds to activate automatic
function.Do not allow interruption to the press cycle. In case of danger, an interruption of the pressing process is possible by pressing the emergency-stop button. After resetting emergency stop situation, re-press ensuring that press head is located in the same position on the fitting.
When press tool completes the press cycle remove from sling.

Release the pressing sling by depressing the arresting latch button.

Push out the locking pins from opposite side and remove press sling from fitting